Showing results: 271 - 285 of 357 items found.
-
81491A -
Keysight Technologies
Keysight's 81491A Reference Transmitter is designed to offer excellent eye quality for NRZ and PAM4 signals at baud-rates up to 32Gbaud and can serve as universal E/O converter. It comes in Multimode (MM) and Single-Mode (SM) flavors and includes internal lasers at 850nm (MM) or 1310&1550nm (SM). External optical input for usage with tunable laser sources is available for SM option. It is fully integrated into Keysight’s Optical Receiver Stress Test solutions to address test requirements of IEEE 802.3 10,40,100 and 400GBASE optical standards.
-
S93084B -
Keysight Technologies
The S93084B tunes the network analyzer’s receivers to the output frequency of the converter under test without having to access internal LOs or a common reference signals. For converters with embedded LOs, this enables measurements of match-corrected conversion loss/gain and absolute group delay (requires S93082B and S93083B), gain compression versus frequency (requires S93086B), intermodulation distortion (requires S93087B), and noise figure (requires S93029B).
-
Spectrum Instrumentation
Adapter Cables connect your Spectrum card or instrument with your device under test, your sensor, your transmitter or receiver, your external machine, your prototype equipment or simply with a probe for measuring. To fulfill a lot of different requirements Spectrum is offering adapter cables between different types of connections and with different length. These adapter cables are manufactured for Spectrum following Spectrum's specification.
-
GFL-T + GFL-R -
Technology Products
The DC Earth Fault locator is suitable to test the DC Battery System and Trace Ground Faults. The system is suitable for Power Plants, Sub-Stations upto 765KV and other industries. The system is highly capable in tracing and pin pointing the DC earth faults in a live system without requiring any shut downs. The receiver sensitivity of 1mA and better is capable to trace most complex fault.
-
NC3208 -
DVTest Inc.
It offers a high ENR output AWGN noise over a wide frequency range. This Noisecom noise source has excellent stability with temperature and voltage for tough environments. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including radar warning receivers (RWR), built-in test equipment (BITE), military aircraft, and Wi-Fi.
-
JSECST™ -
Textron Systems
The Joint Services Electronic Combat Systems Tester (JSECST) is part of the family of testers, supporting the U.S. Air Force, Navy, Army, and over 23 allied nation platforms. JSECST performs full end-to-end diagnostic tests of installed systems including radar warning receivers (RWRs), jamming systems, communication systems, and navigation systems. Our JSECST delivers confidence for flight crews and the technicians who support them. It quickly and accurately tests and fault-isolates electronic combat and avionics systems for today's most advanced combat aircraft.
-
TS-LBS -
Rohde & Schwarz GmbH & Co. KG
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
6TL Engineering
Two pushers plate available for max. DUT areas: 450×450 and 500×650 mm 6tl precision servo pusher H7100 6000 is the recommended solution for PCB test systems combining Functional, In-Circuit, and Hipot Test in one fixture.It is available as a 19″ Rack atonomous module, including all drive, control and safety components for easy integration in automatic test systems using standard Mass Interconnection Receivers.
-
R&S®SMW200A -
Rohde & Schwarz GmbH & Co. KG
Performance and functionality requirements vary depending on test setup and application. The R&S®SMW200A is unrivaled in mastering this challenge and sets new standards for signal generators. When developing and verifying any type of DUT, including component, module and complete base stations – the R&S®SMW200A always easily generates the appropriate test signals with top performance. The flexible modular design of the R&S®SMW200A can be equipped with the exact options required for specific applications. Any configuration is possible, from a classic single-path vector signal generator to a multichannel MIMO receiver tester.
-
M8049A -
Keysight Technologies
The M8049A ISI channel boards can be used to emulate channel loss in receiver test setups. The boards are used to emulate channel loss for data rates of 32 Gb/s and higher. A choice of 21 PC board traces with different lengths can be inserted into the signal path. The trace lengths range from 0.8 inch (20.3 mm) to 22.3 inch (566.4 mm). By cascading the traces within one board or with another board, a wide range of channels can be emulated with very fine resolution of insertion loss steps. With their small size the ISI channel boards can be located closely to the device under test.
-
MS 1721 -
Meltronics Systemtech
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA with ARINC 717 IP Core- One Channel ARINC 717 Transmitter and Receiver- Generates all PCM telemetry signals like NRZ, Bi-Phase, - Differential Bi-phase, DM signals- Used to test all types of PCM based telemetry equipments- Configurable output signals format (parity, word length, Minor, Major frame, Bit position)- User can configure the words and word positions in the frame- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
XF07-518 -
Curtiss-Wright Defense Solutions
The XF07-518 is a rugged quad channel 500MSPS 14-bit digital receiver XMC. The ADC devices are controlled by a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms. The combination of direct high-speed, high-resolution analog I/O port and FPGA processing makes the XF07-518 ideal for demanding applications including radar, imaging and test equipment across commercial and defense market spaces.
-
FSMR3000 -
Rohde & Schwarz GmbH & Co. KG
The R&S®FSMR3000 is a microwave measurement receiver to calibrate signal generators and attenuators with one single instrument. Most important features provided are tuned RF level measurements, level measurements, analog modulation and spectrum analysis. Additionally, the R&S®FSMR3000 can be equipped with powerful hardware for high-end phase noise test supplementary to the standard phase noise test with the spectrum analyzer.
-
RF-LiveSim -
TestTree
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
XF07-516 -
Curtiss-Wright Defense Solutions
The XF07-516 is a rugged quad channel 250MSPS 16-bit digital receiver XMC. The ADC devices directly interfaces to a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms. The combination of direct high-speed, high-resolution analog I/O ports and next FPGA processing makes the XF07-516 ideal for demanding applications including radar, imaging and test equipment across both commercial and defense market spaces.